Select Page

Cycloidal pinwheel reducer is normally a up-dated of brand-new type transmissing machine made with K-H-V less teeth engagement and the cycloidal pin wheel clenching system, which are trusted in drive and minimizing of textile and dying, foodstuff, mining and metallurgy, Oil and chemical conveyors, Market, project machinery etc and cranes. various fields.

1. Gear is made of high power low carbon alloy steel by carburizing and quenching. The hardness of tooth area can reach HRC58-62. CNC grinding technology is used for all good contact effectiveness, with high precision and gears
2. high transmission proficiency: single stage over 96.5%; double stage over 93%; three stage over 90%;
3. stable operation and low noise;
4, compact structure, light-weight, long service lifestyle and high bearing capacity;
5. convenient to check, assemble and disassemble.

Operation specifications and precautions
1.High modularization design: many equip with various engine or other power suggestions conveniently.Same machine type may equip with different power motor. It is easy to realize the combination and
junction between every machine type.
2.Transmission ratio: okay division, wide scope. The combined machine type may form very large transmission ratio, i.e. end result very low rotary speed.
3.Form of set up: the positioning to be installed is not limited.
4.High strength, small: the box body is constructed of excessive strength cast iron. Gear and gear shaft adapts the gas carbonization, quenching and great grinding process, which means bearing capability of unitvolume is excessive.
5.Long life: Beneath the condition of right type chosen (including choosing appropriate operation parameters)normal operation and maintenance, the life span of main elements of speed reducer (except dressed in parts) should not be less than 20000 hours. The wearing parts include lubricating bearing, oil seal and essential oil.
6.Low noise: because main parts of speed reducer are processed, assembled and tested critically,which means noise of speed reducer is low;
7.Parallel axis -bevel wheel speed-down motor
cycloidal gear reducer

1. High speed ratio and efficiency
Single stage transmission can reach to 1 1:87 of speed-downward ratio and the efficiency is going to be more than 90%. If use multi-speed travel the speed-down ratio is usually bigger.
2. Compact
Being adapted epicyclic transmitting principle, the input and end result shaft are in same axis center, it is compact.
3. Smooth and stable run and low noise
The cycloidal pinwheel has more meshed teeth, the overlapping coefficient id big and the device part is stable, the vibration and noise is bound anyway content.
1. Large deceleration ratio
A higher deceleration ratio of 1/30-1/320 can be acquired.The structure is easy, but it can recognize high reduction ratio system.
2. Small gear clearance
The Travel, which meshes with ordinary gears and has minimal backlash, is essential to the controller business.
3. High precision
Multiple teeth are engaged simultaneously, and there are several gears engaged with 180 degree symmetry. Subsequently, the affect of tooth pitch mistake and cumulative tooth pitch error on the rotation precision is relatively average, which makes the positioning precision and rotation accuracy reach an extremely high level.
4. Less parts, easy installation
The three basic elements achieve a higher deceleration ratio, plus they are all on the same axis, therefore the kit is simple to install and easy to shape.
5. Small in size and light in weight
Compared with the prior gear device, the volume is 1/3, the weight is 1/2, but can buy the same torque capability and reduction ratio, reaching small lightweight.
6 High torque capacity
Flexible wheel material USES exceptional steel with high fatigue strength.Not the same as ordinary transmission product, the amount of teeth meshing accounts for relevant to 30% of the total amount of teeth. Furthermore, it is in contact with the surface, so that the pressure borne by each gear is reduced and excessive torque potential can be obtained.
7 High efficiency
The sliding of gear meshing parts is very small, which reduces the power loss caused by friction. Therefore, high lowering ratio may be accomplished while maintaining high efficiency, and miniaturization of driving motor could be realized.
8. Low noise
The gear meshing cycle velocity is low, the transmission motion force balance, therefore the procedure is quiet, and the vibration is very small.
◆High speed ratio and high efficiency single-stage transmission can achieve a deceleration ratio of just one 1:87, and the efficiency is a lot more than 90%. If multi-stage transmission can be used, the deceleration ratio will end up being larger.
◆Because planetary transmission basic principle is adopted, the type shaft and productivity shaft are on the same axis line, so that the machine version can get the smallest possible size.
◆The number of meshing teeth of cycloidal needle teeth with smooth running noise and low cycloidal noise is more, the overlap coefficient is greater, and the mechanism of balancing machine parts will make the vibration and voice limited to a minimum.
◆Reliable use and prolonged service life for the reason that primary parts are constructed of huge carbon chromium steel, large strength is usually obtained by quenching (HRC58-62), and rolling friction is employed in some transmission contacts, therefore the service life is very long.
Cycloid reducer is a cycloid needle teeth meshing planetary transmission principle drive models, is a perfect transmission has various advantages, versatile, and can be both positive and negative operation.

•Big ratio, and high efficiency Smooth operation,

• low noise The usage of reliable,

• extended life can reach 50000 hours

• Main parts high-carbon the Ming-steel after quenching treatment (HRC58-62),

• operation and connection with rolling friction, basically no wear, durable.

• Compact structure,

• tiny size Because the utilization of a planetary transmitting, the suggestions shaft and the output shaft on the same axis, which makes the model to obtain the smallest possible size.

• Reasonable design, easy repair, and breakdown easily install,

• the least number of parts along with basic lubrication, cycloid reducer trusted by an individual.
(1)Size above PL/PF120(including)high torque products adopt integral double wall world pinion carrier, precision and enhance the output strength.

(2).Hoop clamp coupling have five connection methods suitable for different application environments.

(3).Size above PL/PF120(including)precision and high strength integral inner gear housing, processed in a single station,which eliminate the cumulative error and assembling error of split type.Remove casting process;adopt incredibly hot of forging process, which will reduce the blank material defects.

(4).The meshing gear adopt shaving method after carburizing and quenching,which simpler to make gear surface smooth and high accuracy,decrease the temperature rising caused by gear surface gluing and friction.
This series worm-gear reducer was engineered after RV worm microreducer, which have a complete norm, wide speed for selection, and many mounting positions. Its overall performance and mounting dime nsions conform the same sorts of foreign.
The combination of worm and gear has higher efficiency and wider speed range to single worm.
Designation of square shape, compact structure, beautiful shape, low noise and radiate heat efficiently.
Good sealing and adaptability.Its mixture with T gear reducer and MB/MBN variator may meet a myriad of speed requirement.